Product Sheet
General Description:
Curramix 2500 is an advanced single part ambient-cure anti-coking ceramic coating system designed specifically for high temperature metal substrates and components. This coating exhibits state of the art coating technology with exponential improvements in thermal cycling and anti-coking properties. Designed to withstand extreme temperatures up to 2000°F. Ideally suited for heat exchanger tubes, tube sheets, channels, exchanger components and crude heaters. Can be done in-situ.
Benefits:
- Excellent Hydrophobic & Oleophobic properties
- Excellent foul release.
- Reduction in drag
- Coating surface remains smooth even at high temperatures.
- Excellent adhesion
- Thermal shock resistant
- Minimal Porosity
- Resists micro-cracking & spalling
- VOC exempt
Coating Properties:
Base: Color Varies; Liquid
Packaging: 1 Gallon kit
Solids by weight: 74% (+/- 2%)
Mandrel Bend: (ASTM D 522)
4mm loss at 180° rotation
Chemical resistant:
Contact Curran International for specific chemicals/temperatures/concentrations.
Recommended for extremely high temperatures and thermal cycling
Hardness:
(Pencil-ASTM D3363)
9h
(Scratch-ASTM D3363)
5b
Adhesion Cross Cut Tape:
(ASTM D3359)
5b
Temperature resistance:
2000°F thermally cycled
Contact Curran on particular service conditions.
Theoretical coverage:
- Per one-gallon kit at 1 mil 1180 ft2
Application:
Below are general guidelines for applying Curramix 2500. Contact Curran International for detailed application procedures.
Surface preparation:
- All surfaces shall be clean, dry, and oil free prior to the start of surface preparation.
- Chlorides shall be less than 10 ppm.
- Minimum surface cleanliness: SSPC- SP 10, NACE 2.0; SA 2.5.
- The surface profile must be a lightly blasted profile
- For best results use dry grit garnet 100-120 mesh
- Coating shall be applied immediately after surface preparation.
Environmental:
Apply when substrate temperature is between 60°F(15°C) and 100°F(37°C). Substrate must be 5°F(3°C) above dew point
Mixing:
- Shake the product to completely mix.
- Shake loose all solids on bottom to ensure full mix
- Failure to fully mix will result in product failure due to poor chemical ratios
Coating Spray Application:
- Curramix 2500 can be spray applied by siphon-feed detail gun.
- Clean tools with acetone after use
Recommended Dry Film Thickness:
- One coat system for target DFT of .25 – 2 mils (6.4 -50.8 microns)
Repairs:
Should the coating be mechanically damaged contact Curran international for repair procedure.
Storage/Shelf Life:
Store in temperatures between 50°F (10°C) and 90°F (32°C); 12 months from original shipped date
Health and Safety:
Prior to using this product please review the appropriate Safety Data Sheet (SDS).
Cure Time:
| 70F/21C | |
| Task Free (Minimum) | 35 min |
| Partial Cure | 24 Hrs |
| Full Cure | 120 Hrs |
The information in this data sheet is based on laboratory tests we believe to be accurate and is intended for guidance only. All recommendations or suggestions relating to the use of this product, whether in technical documentation, or in response to a specific enquiry, or otherwise, are based on data which to the best of our knowledge are reliable. Because the only true reliable test is one that is in actual operation, Curran International will make available at no charge, samples of the material for testing purposes. Curran International has no control over either the quality or the condition of the substrate, or the many factors affecting the use and application of the material. Curran International does therefore not accept any liability arising from loss, injury or damage resulting from such use or the contents of this data sheet (unless there are written agreements stating otherwise). The data contained herein are liable to modification as a result of practical experience and continuous development. This data sheet replaces and annuls all previous issues, and it is therefore the user’s responsibility to ensure that this data sheet is current prior to using the product.